25 ways to fix a broken tap or drill bit in a hole!
How to fix the broken tap and drill bit in the hole? Let's take a look at these 25 methods!
1. Pour some lubricating oil, use a pointed hairpin or chisel to slowly knock out the broken surface in the opposite direction, and occasionally pour iron chipping (the most commonly used method in the workshop, but it may not be suitable for threaded holes with too small apertures or broken taps that are too long, but you can try it).
2. Weld a handle or hexagonal nut on the broken section of the tap, and then gently reverse it out (which is originally a good method, but welding is a bit troublesome. If the same is true, it is not suitable for smaller diameter taps);
3. Use a special tool: a tap extractor, which works by connecting the workpiece and tap to positive and negative electrodes respectively, and filling the middle with electrolyte,
Causing the workpiece to discharge and corrode the tap, and then assisting with pointed nose pliers to remove it, causing minimal damage to the inner hole;
4. Use a steel roller to push against the crack in the tap and slowly tap it with a small hammer. The tap is relatively brittle, but it will eventually become slag and come out. Alternatively, simply drill and bore the threaded hole of the broken tap, and then re drill and tap it (the method is somewhat barbaric. If the tap diameter is too small, it is not easy to use, and if the diameter is too large, tapping can be quite tiring);
5. Weld the threaded hole where the broken tap is located flat, grind it flat again, and re drill. Although it is difficult, it can be slowly drilled in (if the threaded hole can be changed in position, it is recommended to replace it with the original threaded hole when re drilling and tapping);
6. Drill a slot on the cross-section of the broken tap and screw it up in the opposite direction with a screwdriver (that slot is difficult to chisel out, especially if the tap diameter is small);
7. Drill the threaded hole of the broken tap, then insert a steel wire insert or pin, then weld, grind it flat, and drill and tap again to achieve basic consistency (although this method is troublesome, it is very practical, and the size of the tap does not matter);
8. Use electric pulses to break it, electric spark or wire cutting can be used. If the hole is damaged, you can expand it and add a steel wire screw sleeve (this method is simpler and more convenient, and coaxiality should not be considered temporarily, unless the coaxiality of your threaded hole directly affects the quality of the equipment);
9. Make a simple tool and insert it into the empty slot of the chip removal slot on the cross-section of the broken tap. Be careful to pull it out in the opposite direction. For example, you can use a broken tap with a square tenon to tighten two nuts, insert a steel wire (with the same number of slots as the tap) into the empty slot of the broken tap and the nut, and then use a hinge to pull the square tenon in the direction of retraction, Remove the broken tap (the main idea of this method is to connect the chip removal groove of the broken tap and use steel wire, preferably a steel needle to make a specialized wrench for removing broken threads. Of course, if such broken threads often occur in the workshop, it is better to make a tool wrench like this);
10. Nitric acid solution can corrode high-speed steel wire cones and does not scrap workpieces;
11. Anneal the tap with an acetylene flame or spray lamp, and then use a drill bit to drill. At this time, the diameter of the drill bit should be smaller than the diameter of the bottom hole, and the drill hole should also be aligned with the center to prevent thread damage. After drilling the hole, insert a flat or square punch and use a wrench to unscrew the tap;
12. Use an air drill to reverse the rotation, relying entirely on hand feel, because it is not directly drilling out the tap, but using slow speed and a little bit of friction (similar to a car semi clutch) to make the tap rotate out along with it;
13. You can use a grinder to smooth out the broken wire, then use a small drill bit to drill first, and gradually switch to a larger drill bit. The broken wire will gradually fall off, and after falling off, use the original size tap to re tap the tooth. This advantage can avoid increasing the aperture;
14. Weld an iron rod onto the broken object and then unscrew it. (Disadvantages: Too small broken objects cannot be welded; extremely high welding skills are required, which can easily burn the workpiece; the welding area is prone to breakage, and the probability of removing broken objects is very low.)
15. Use a cone-shaped tool harder than the broken object to pry. (Disadvantages: Only suitable for brittle fracture materials. Crush the fracture material and slowly remove it; the fracture material is too deep or too small to be removed; it is easy to damage the original hole)
16. Make a hexagonal electrode with a smaller diameter than the cutting object, use an electric discharge machine to machine a hexagonal countersunk hole on the cutting object, and then use an internal hexagonal wrench to unscrew it. (Disadvantages: useless for rusty or stuck broken objects; useless for large workpieces; useless for too small broken objects; time-consuming and laborious)
17. Use an electrode smaller than the broken object directly and use an electric spark machine to strike. (Disadvantages: It is useless for large workpieces and cannot be placed on the workbench of electric discharge machine tools; time-consuming; when it is too deep, it is easy to accumulate carbon and cannot be driven down)
18. Using an alloy drill bit to drill (disadvantages: easy to damage the original hole; useless for hard objects; alloy drill bits are brittle and easy to break)
19. There is now a portable tool machine designed and manufactured using the principle of electrical machining, which can easily and quickly remove broken screws, broken tap drill bits.
20. If the screw is not too hard, you can flatten the end face, find the center point, punch a small point with a sample, use a smaller drill bit to drill first, make it vertical, and then use a broken wire extractor to unscrew it in the opposite direction.
21. If you cannot buy a broken thread extractor, use a larger drill bit to continue expanding the hole. When the hole diameter approaches the screw, some threads may lose their grip and fall off. Remove the remaining threads and use a tap to readjust.
22. If the screw is broken and exposed, or if the requirements for the broken screw are not strict, and it can be sawed with a hand saw, the gap can be sawed, even the outer shell can be sawed, and then removed with a flat screwdriver.
23. If the broken wire is exposed for a certain length outside and the melting point of the mechanical material is not too low, an extended T-shaped rod can be welded onto the screw by electric welding, so that it can be easily screwed out from the welded rod.
24. If the screws rust severely and are difficult to handle using the above methods, it is recommended to heat them red and add a little lubricating oil, then use the corresponding methods above to handle them.
After more than N efforts, although the screw was removed, the hole was also discarded. Instead, a larger hole could be drilled and tapped. If there are limitations on the position and size of the original screw, a larger screw can be drilled in, or it can be directly welded and tapped, and then a small hole can be drilled and tapped in the center of the larger screw. But sometimes it can be difficult to tap the internal metal structure after welding.

