Knowledge

CNC machining center operation experience, the most comprehensive summary!

The process of CNC machining

1) Read drawings and program sheets

2) Transfer the corresponding program to the machine tool

3) Check program header, cutting parameters, etc

4) Determination of machining dimensions and allowances on workpieces

5) Reasonable clamping of workpieces

6) Accurate alignment of workpieces

7) Accurate establishment of workpiece coordinates

8) Reasonable selection of cutting tools and cutting parameters

9) Reasonable clamping of cutting tools

10) Safe trial cutting method

11) Observation of the Processing Process

12) Adjustment of cutting parameters

13) Timely feedback on issues and corresponding personnel during the processing

14) Inspection of workpiece quality after processing

Precautions before processing

1) For new molds, the processing drawings must meet the requirements and the data must be clear; The processing drawing of the new mold should have the signature of the supervisor, and all columns of the processing drawing have been filled in.

2) The workpiece has a qualified label from the quality department.

3) After receiving the program order, check whether the workpiece reference position is consistent with the drawing reference position.

4) Check each requirement on the program sheet carefully, confirm whether the program is consistent with the drawing requirements, and if there are any problems, work together with the programmer and production team to solve them.

5) Based on the material and size of the workpiece, determine the rationality of the programmer's selection of cutting tools for rough or light cutting programs. If it is found that the tool application is unreasonable, the programmer should be immediately notified to make corresponding changes in order to improve machining efficiency and workpiece machining accuracy.

Precautions for clamping workpieces

1) When clamping the workpiece, pay attention to the position of the code and the appropriate extension length of the nut and bolt on the pressure plate. In addition, the screw should not be pushed to the bottom when locking the corner.

2) Copper bars are generally processed for locking plates. Before starting the machine, the cutting quantity on the program sheet should be checked to ensure consistency, and the screws on the receiving plate should be checked for tightness.

3) For the case of collecting multiple copper pieces on one board, it is necessary to check whether the direction is correct and whether there is interference during the processing of each copper piece.

4) According to the shape of the program sheet and the size data of the workpiece, it is necessary to note that the writing of the workpiece size data is XxYxZ. At the same time, if there is a loose part drawing, it is necessary to check whether the graphics on the program sheet match the graphics on the loose part drawing, pay attention to which direction to go out, and the swing of the X and Y axes.

5) When clamping workpieces, it is necessary to check whether the dimensions of the workpiece meet the size requirements of the program sheet. If there is a loose part drawing, it is necessary to check whether the dimensions of the program sheet are the same as those of the loose part drawing.

6) The workbench and the bottom of the workpiece should be cleaned before the workpiece is put on the machine. The machine tool table and workpiece surface should be pushed away with oilstone to remove burrs and damaged areas.

7) When coding, ensure that the code is not damaged by a knife and communicate with a programmer if necessary. Meanwhile, if the bottom pad is square, the code must be aligned with the position of the square pad to achieve force balance.

8) When using pliers to clamp, it is necessary to understand the machining depth of the tool to prevent the clamped position from being too long or too short.

9) The screws must be inserted into the T-shaped block, and only a part of the thread must be used. If screws need to be connected, half of the joint thread must be used for the upper and lower screws, and the thread of the nut on the pressure plate must be fully used, not just a few threads.

10) When determining the depth of Z, it is necessary to clearly see the position of the program's single touch count and the data of the highest point of Z. After inputting the data into the machine tool, it must be checked again.

▌ Precautions for clamping cutting tools

1) The tool should be securely clamped and not too short in the handle.

2) Before each cutting, it is necessary to check whether the cutting tool meets the requirements. The length of the cutting tool should be determined according to the machining depth indicated in the program sheet, generally slightly longer than the machining depth value by 2mm, and consideration should be given to whether the tool holder collides.

3) When encountering situations where the processing depth is very deep, you can communicate with the programmer and use a two-stage cutting method as appropriate, that is, first cutting half to 2/3 of the length, and then cutting longer when the processing reaches a deeper position, which can improve processing efficiency.

4) When using an extended cable nozzle, it is particularly important to understand the depth of the blade and the required length of the blade.

5) Before installing the cutting head on the machine, the taper fitting position should be wiped clean with a cleaning cloth, and the corresponding position of the machine tool sleeve should also be cleaned to avoid iron filings on the fitting surface affecting accuracy and damaging the machine tool.

6) Usually, the tool length is adjusted using the tip alignment method (in special cases, the tool is aligned within the tool), and the instructions on the program sheet should be carefully checked during alignment.

7) When the program is interrupted or needs to be re aligned, attention should be paid to whether the depth can be connected to the front. Generally, the depth can be adjusted by 0.1mm first, and then adjusted according to the situation.

8) Rotating detachable cutting heads, if using water-soluble cutting fluid, should be lubricated with oil for several hours every half month for maintenance, which can lubricate the internal components of the cutting head and prevent wear.

Precautions for correcting and aligning workpieces

1) When dragging the workpiece, attention must be paid to its verticality. One side should be smoothed before dragging the vertical edge.

2) When dividing the workpiece, it must be verified twice.

3) After counting, the center position should be checked based on the external dimensions provided in the program sheet and the dimensions on the component drawing.

4) All workpieces must be centered using the centering method, and the zero position on the edge of the workpiece must also be centered using the centering method before being moved to the edge, ensuring that the margin on both sides is consistent. If it is necessary to take data unilaterally in special circumstances, confirmation from the production team must be obtained again before passing. After counting on one side, remember to compensate for the radius of the dividing rod.

5) The zero position input of the workpiece center must be the same as the three-axis center in the workstation computer diagram.

▌ Precautions during processing

1) When manually removing excess on the top surface of the workpiece with a large knife, remember not to use a deep gong.

2) The most important step in machining is the first cutting, as careful operation and verification can reveal whether the tool length, diameter, program, speed, etc. are correct, avoiding damage to the workpiece, tool, and machine tool.

3) Try cutting the program in the following way:

a) The first point is that the maximum height should be raised by 100mm. Use your eyes to feel if it is correct;

b) Control the "fast movement" to 25% and the feed rate to 0%;

c) When the tool approaches (about 10mm) the machining surface, pause the machine;

d) Check if the remaining itinerary and program are correct;

e) After restarting, place one hand on the pause button, ready to stop at any time, and control the feed rate with the other hand;

f) When the tool is very close to the workpiece surface, it can be stopped again, and the remaining stroke of the Z-axis must be checked.

g) After the machining and cutting process is smooth and stable, adjust all controls back to normal state.

4) After entering the program name, use a pen to copy back the program name on the screen, and then check it against the program sheet. When opening the program, pay attention to checking whether the tool diameter size in the program matches the program sheet, and immediately fill in the file name and tool diameter size in the signature column of the processor on the program sheet. It is forbidden to fill in afterwards or in advance.

5) In principle, NC technicians are not allowed to leave during the rough cutting of workpieces. If it is necessary to leave in case of changing tools or assisting in adjusting other machine tools, other NC team members must be invited or come back regularly for inspection.

6) When doing medium light cutting, NC technicians should pay special attention to the areas where they did not open the rough cutting to prevent the tool from hitting this area.

7) Program cutting. If the program is interrupted during processing and too much time is wasted starting from scratch, the team leader and programmer should be notified to modify the program and cut off the already executed parts.

8) Program exception. If there is an abnormal situation in the program and there is no certainty, you can lift it up to observe the process and then decide on the next action.

9) The line speed and rotational speed provided by the programmer during the machining process can be adjusted by the NC technician according to the situation. However, special attention should be paid to the fact that the speed of small copper parts should not be too fast when exposed to coarse materials, in order to avoid loosening of the workpiece due to oscillation.

10) During the machining process of the workpiece, the NC technician should check with the loose part drawing to see if there are any abnormal conditions. Once a discrepancy is found between the two, the machine must be stopped immediately and the team leader must be notified to verify if there are any errors.

11) When using cutting tools longer than 200mm for machining, attention must be paid to issues such as clearance, feed depth, rotation speed, and travel speed to avoid tool swinging. At the same time, the travel speed of the corner position should be controlled.

12) For those who require the detection of tool diameter on the program sheet, the operator must be responsible and record the tested diameter. If it exceeds the tolerance range, it should be immediately reported to the team leader or replaced.

13) When the machine tool is operating automatically or has free time, the operator should go to the workstation to learn about the remaining machining programming situation, prepare and grind appropriate tools for the next machining backup, in order to avoid shutdown.

14) Process errors are the main reasons for wasting time: incorrect use of inappropriate cutting tools, incorrect scheduling of processing, wasting time in positions that do not require processing or non computer processing, improper use of processing conditions (such as slow speed, empty cutting, dense cutting path, slow feed, etc.). When these events occur, they can be addressed through programming and other means.

15) During the machining process, it is necessary to pay attention to the wear of the cutting tools and replace the cutting particles or tools appropriately. After replacing the cutting particles, pay attention to whether the joint boundaries of the machining match.

▌ Precautions after processing completion

1) Confirm that each program and instruction required by the program sheet have been completed.

2) After the processing is completed, it is necessary to check whether the shape of the workpiece meets the requirements, and at the same time, perform self inspection of the workpiece size according to the loose part drawing or process drawing to timely detect errors.

3) Check for any abnormalities in the various positions of the workpiece. If there are any questions, notify the NC team leader.

4) Notify the team leader, programmer, and production team leader when removing larger workpieces from the machine.

5) Pay attention to safety when removing workpieces from the machine, especially when removing larger workpieces, protect both the workpiece and the NC machine.

Differentiated treatment of machining accuracy requirements

Surface quality of Jingguang:

1) Molten and inlaid blocks

2) Copper Gong

3) Avoid empty spaces at the top pin plate support head holes, etc

4) Eliminate the phenomenon of vibration knife marks

Size of Jingguang:

1) Measurable dimensions must be strictly inspected after processing

2) When processing for a long time, it is necessary to consider the wear and tear of the cutting tools, especially at the sealing position and other critical points

3) Jingguang should use new hard alloy cutting tools as much as possible

4) Determine the minimum modulus after polishing according to the processing requirements

5) Confirmation of quality after processing, production, and other aspects

6) Control tool wear during sealing position processing according to processing requirements

▌ Take over the shift

1) Confirm the homework status of work hours, including processing status, mold status, etc.

2) Confirm if the equipment is working properly during work hours.

3) Other handover and confirmation, including drawings, program sheets, cutting tools, measuring tools, fixtures, etc.

Workplace organization

1) Follow the 5S requirements.

2) Cutting tools, measuring tools, fixtures, workpieces, tools, etc. are neatly arranged and classified.

3) Cleaning of machine tools.

4) Cleaning of the workplace floor.

5) Return of processed tools, idle tools, and measuring tools to the warehouse.

6) Processed workpieces are sent for quality inspection or corresponding departments.

You Might Also Like

Send Inquiry