Knowledge

Troubleshooting methods for tapping faults in Fanuc system machining center

The following are the troubleshooting methods for tapping faults in the vertical machining center of Fanuc system:

Troubleshooting of tap breakage

-Check parameter settings:

-Check the feed rate (F-value) and spindle speed (S-value) in the tapping program. The correct relationship between feed rate and rotational speed should meet the pitch requirements of the thread, that is, F=S × pitch. For example, when attacking an M8 × 1.25 thread and setting the speed to 1000r/min, the feed rate should be set to 1250mm/min.

-Ensure that the tapping method parameters are correct. If the selection of rigid tapping and flexible tapping modes is appropriate, rigid tapping requires high synchronization of the machine tool and is suitable for high-precision applications; Flexible tapping has a certain buffer to avoid damage to the tap.

-Check the condition of the bottom hole:

-Re measure the diameter of the bottom hole to ensure it meets the standard. For example, for ordinary coarse thread, the diameter of the bottom hole is generally equal to the nominal diameter minus the pitch.

-Attention should also be paid to the machining accuracy of the bottom hole. Poor cylindricity of the bottom hole may also cause the tap to break. It is necessary to ensure the machining quality of the bottom hole.

-Improve chip removal condition:

-Adjust the flow rate and pressure of the cutting fluid to effectively flush the chips into the feed process.

-For blind hole tapping, a spiral groove tap can be used, which has good chip removal performance and can discharge chips upwards.

Troubleshooting of thread accuracy deviation

-Tool inspection and replacement:

-Use magnifying glass and other tools to check the wear of the tap edge, and replace the severely worn tap in a timely manner.

-Select high-quality and high-precision taps to ensure that the manufacturing accuracy of the taps meets the processing requirements.

-Machine tool accuracy detection and adjustment:

-Use professional inspection tools to check the axial and radial runout of the machine tool spindle. If the jumping exceeds the range, the spindle needs to be repaired or adjusted.

-Check if the worktable of the machine tool is level. If it is not level, it will affect the verticality of the tapping and thus affect the thread accuracy.

-Program inspection and correction:

-Carefully check the parameters of the thread pitch, starting position, ending position, etc. in the program to ensure consistency with the machining requirements.

-When processing threads of different specifications, the parameters in the program should be modified accordingly.

Troubleshooting of tapping overload alarm

-Reduce cutting resistance:

-Pre treat the workpiece material, such as normalizing, annealing, and other heat treatments, to reduce material hardness.

-Optimize processing technology, arrange machining allowance reasonably, and ensure even allowance.

-Check the motor and driver:

-Check if the current of the motor is within the rated range. Excessive current may indicate motor overload.

-Check the parameter settings and working status of the drive, check for alarm codes, and troubleshoot according to the code prompts. If the drive has poor heat dissipation, it may cause abnormal operation, and its heat dissipation device should be checked.

The tapping of the vertical machining center of Fanuc system has been suspended for various periods of time, mainly due to the following reasons:

Parameter setting issue

-Unreasonable acceleration and deceleration time constants: During the tapping process, if the acceleration and deceleration time constants of the spindle and tapping axis are not set properly, the movements of the two cannot be well matched, resulting in a pause in tapping. For example, if the acceleration and deceleration time is too long, it will cause the tapping shaft to pause before reaching the set speed

-Synchronization parameter setting error: When rigidly tapping, the synchronization parameter setting between the spindle and the tapping axis is incorrect, which can cause the two to be unable to maintain precise synchronization during the tapping process, resulting in a pause phenomenon. If the position loop gain parameter of the tapping axis is set improperly, it will affect the following performance of the tapping axis and cause a pause

Mechanical transmission issues

-Loose or worn transmission chain: If the gears, belts, couplings and other components in the machine tool transmission chain are loose, worn or have excessive clearance, it will cause unstable power transmission during the tapping process, resulting in intermittent pauses in the movement of the tapping shaft.

-Tap clamping problem: If the tap clamping is not firm or the clamping accuracy is insufficient, the tap will swing or shift during tapping, increasing the tapping resistance. The machine tool control system will pause tapping to protect the tool and machine tool.

Control system issues

-Signal interference: Strong electromagnetic interference around the machining center or poor grounding of the control system can cause the control system to receive incorrect signals, resulting in a pause in tapping.

-System program failure: Errors, vulnerabilities, or missing programs in the CNC system can affect the normal operation of tapping, causing abnormal pauses in the movement of the tapping axis.

Cutting condition issues

-Excessive cutting force: Improper selection of tapping parameters, such as too fast feed rate or too low speed, can result in excessive cutting force that exceeds the capacity of the machine tool or tap, causing the machine tool to pause tapping to avoid damage

-Poor chip removal: chips accumulate in the hole, which increases the tapping resistance. When the resistance reaches a certain level, the machine tool will pause tapping and wait for the chips to be discharged before continuing.

To determine the reasonable value of the acceleration and deceleration time constant in the Fanuc system, the following methods can be referred to:

Refer to the machine manual and technical documentation

The manuals and technical documents provided by machine tool manufacturers will provide recommended acceleration and deceleration time constant values, which are determined based on the mechanical structure, motor performance, and other characteristics of the machine tool and can serve as important reference basis.

Based on processing technology and materials

-Cutting feed: When machining materials with high hardness, such as titanium alloys, in order to reduce cutting force and tool wear, the acceleration and deceleration time constants should be appropriately extended to reduce the rate of change in feed rate; When processing softer materials such as aluminum, the time constant can be correspondingly shortened to improve processing efficiency

-Rapid feed: When performing rapid positioning or idle movement, the acceleration and deceleration time constants can be appropriately reduced within the allowable range of the machine tool to shorten the positioning time, but attention should be paid to avoiding impact caused by too fast acceleration and deceleration.

Utilize system diagnostic and monitoring functions

The Fanuc system provides diagnostic parameters and monitoring screens. For example, during rigid tapping, the values of diagnostic parameters 452 and 453 can be observed to adjust the acceleration and deceleration time constants. Generally, the value of 453 should be less than 10% to ensure the synchronization accuracy between the spindle and the tapping axis

Conduct trial cutting and optimization adjustments

-Initial selection parameters: First, set the acceleration and deceleration time constant based on experience or the above methods. For example, the acceleration and deceleration time constant after cutting feed interpolation is 1622, which can be set to a value between 100-500ms

-Trial cutting evaluation: Conduct trial cutting and observe the smoothness of motion, machining accuracy, tool wear, and other conditions during the machining process. If there are problems such as vibration and accuracy deviation, it may be due to unreasonable acceleration and deceleration time constants.

-Gradual optimization: Based on the trial cutting results, gradually adjust the acceleration and deceleration time constants in small increments, such as 10% -20% each time, and then try cutting again until the best processing effect is achieved.

Adjust the acceleration and deceleration time constant through the monitoring screen of the Fanuc system

1. Enter the monitoring screen

-Firstly, on the Fanuc system operation panel, press the "SYSTEM" button. Then find the "Diagnosis" or "Parameters" option in the system menu (the specific name may vary slightly depending on the system version and machine manufacturer settings), and enter to find the relevant monitoring screen.

2. Search for parameters related to acceleration and deceleration display

-In the monitoring screen, it is necessary to find the parameters related to the acceleration and deceleration time constants. For example, for the acceleration and deceleration time constants of the feed axis, there may be specialized parameter numbers (such as parameter 1622, used for the acceleration and deceleration time constants after cutting feed interpolation). These parameters will display the currently set values.

-For rigid tapping, special attention should be paid to parameters such as diagnostic parameters 452 and 453. The value of parameter 453 should be as small as possible, less than 10%, as it can help determine the synchronization accuracy between the spindle and the tapping axis, thereby indirectly guiding the adjustment of acceleration and deceleration time constants.

3. Adjust according to the displayed data

-If the parameter values displayed on the monitoring screen do not meet expectations, such as the synchronization accuracy parameter 453 being too large, it is necessary to adjust the acceleration and deceleration time constants.

-Return to the "Parameters" setting interface (usually with a separate "Parameters" option in the system menu) and find the corresponding acceleration and deceleration time constant parameter (such as parameter 1622 mentioned above). Modify the parameter values in appropriate increments (such as 10-20ms per adjustment) based on the actual situation of the machine tool and the trial cutting effect.

-After the adjustment is completed, perform the machining operation again, observe the parameter changes in the monitoring screen and the actual machining effect, such as the smoothness of the motion, tapping accuracy, etc. If the processing effect does not improve or even deteriorates, it is necessary to readjust the parameter values until a satisfactory processing effect is achieved.

You Might Also Like

Send Inquiry