Knowledge

Omni directional dissection of drill bits

Drill bits are commonly used, but have you analyzed them comprehensively? What is the name of each part of it? What are the characteristics? What if it breaks down? What should I do if there are burrs? Now I have everything organized for you, take it away~
Omni directional dissection drill bit
The name of the drill bit

微信图片_20221109141326.jpg

Professional Name

微信图片_20221109141333.jpg

① Spiral angle γ: Different models have different angles, usually ranging from 10 to 40 degrees.
② Blade band: mainly used for guiding and squeezing purposes.
③ Blade back: The area between the blade and groove, but lower than the blade, reducing cutting force (friction).
④ Chip removal groove surface: Sometimes it is the front cutting surface, the surface through which chips flow.
⑤ Drill sharp angle: the intersection point between the cutting edge and the cutting edge.
The angle of the drill bit

微信图片_20221109141333.jpg

⑥ Main cutting edge: The angle between the two main cutting edges is the top angle б, The true cutting part.
⑦ Back cutting surface: forming a back angle α Face.
⑧ Horizontal blade: The part that connects two cutting wedges and bears 50% of the cutting force (axial).
⑨ Knife back clearance: reduces the friction between the drill bit and the workpiece.
⑩ Chip removal groove: Large space, conducive to chip removal.
Are there any issues with hole notches and burrs?
Improving the width and height of the drill tip against the workpiece by reducing the drill tip angle
Smaller drill tip angle 118 °
1. Radial force component, poor radial stability.
2. Small axial force.
3. Non ductile materials reduce fragmentation.
Large drill tip angle of 135 ° -140 °
1. Large axial separation and good radial stability.
2. Greater feed capacity.
3. Soft adhesive material reduces flash.
4. The roundness, diameter tolerance, and straightness of the hole are better.
Peripheral chamfered drill tip
1. Reduce fragmentation.
2. The advantage of having a large sharp angle drill bit.
Drill bit application issues/measures
Drill tip wear

微信图片_20221109141345.jpg

Reason:
1. The workpiece will move downward under the force of the drill bit, and the drill bit will bounce back after drilling
2. Insufficient rigidity of the machine tool
3. The drill bit material is not strong enough
4. The drill bit jumps too much
5. Insufficient clamping rigidity, causing the drill bit to slide

微信图片_20221109141348.jpg

Measures:
1. Reduce cutting speed
2. Increase feed rate
3. Adjust the cooling direction (internal cooling)
4. Add a chamfer
5. Check and adjust the coaxiality of the drill bit
6. Check if the rear corner is reasonable
Broken or damaged blades

微信图片_20221109141352.jpg

Reason:
1. The installation vibration of the drill bit is caused by excessive impact on one cutting edge.
2. The clamping rigidity of the workpiece is low, which occurs during drilling and cutting.
3. Excessive feed rate.
4. The cutting speed is too high.

微信图片_20221109141355.jpg

Measures:
1. Adjust the installation vibration to below 0.02mm, so that the two edges of the drill bit can be machined under balanced conditions.
2. Reduce the feed rate and reduce the impact when the drill bit cuts out.
If it is a rotatable drill bit, replace the blade material.

 

Accretion tumor

微信图片_20221109141358.jpg

Reason:
1. Chemical reactions between cutting materials and workpiece materials (low carbon steel with high carbon content)

微信图片_20221109141401.jpg

Measures:
1. Improve lubricants and increase oil or additive content
2. Increase cutting speed, reduce feed rate, and reduce contact time
3. If drilling aluminum, a surface polished uncoated drill bit can be used
Broken knife

微信图片_20221109141404.jpg

Reason:
1. The spiral groove of the drill bit is blocked by chips and the cutting is not discharged in a timely manner
When drilling through the hole quickly, there is no reduction in feed rate or change of motion to manual feed
When drilling soft metals such as brass, the back corner of the drill bit is too large and the front corner is not polished, causing the drill bit to automatically rotate in
4. The grinding of the drill blade is too sharp, resulting in blade breakage and failure to quickly retract the blade
Measures:
1. Shorten the cycle of tool replacement
2. Improve installation and fixation, such as increasing support area and increasing clamping force
3. Check the spindle bearings and sliding grooves
4. Use high-precision tool holders, such as hydraulic tool holders
5. Use materials with stronger toughness

You Might Also Like

Send Inquiry