Knowledge

10 common problems in deep hole machining

In the process of deep hole machining, problems such as dimensional accuracy, surface quality, and tool life of the workpiece are often encountered. How to reduce or even avoid these problems is currently an urgent problem that we need to solve. Below is a summary of 10 common problems and solutions in deep hole machining.
1.
Increased aperture results in large errors
1) Cause of occurrence
The design value of the outer diameter size of the reamer is too large or there are burrs on the cutting edge of the reamer; Cutting speed too high; Improper feed rate or excessive machining allowance; The main deviation angle of the reamer is too large; Bending of the reamer; Adhesion of chips on the cutting edge of the hinge cutting; When grinding, the swing deviation of the hinge cutting edge exceeds the tolerance; Improper selection of cutting fluid; When installing the reamer, the surface of the cone handle is not cleaned of oil stains or the cone surface is scratched or damaged; The flat tail of the taper shank is offset and interferes with the taper shank after being installed into the spindle of the machine tool; The spindle is bent or the spindle bearings are too loose or damaged; The floating of the reamer is not flexible; When the axis is different from the workpiece and the hand is used for reaming, the force on both hands is uneven, causing the reamer to shake left and right.
2) Solution measures
Reduce the outer diameter of the reamer appropriately according to the specific situation; Reduce cutting speed; Adjust the feed rate appropriately or reduce the machining allowance; Reduce the main deviation angle appropriately; Straighten or scrap bent and unusable reamers; Carefully trim with an oilstone to meet the requirements; Control the swing within the allowable range; Choose cutting fluids with better cooling performance; Before installing the reamer, the internal oil stains on the reamer taper handle and the spindle taper hole of the machine tool must be wiped clean, and any bumps on the taper surface must be polished with an oilstone; Grinding the flat tail of the reamer; Adjust or replace the spindle bearings; Readjust the floating card head and adjust the coaxiality; Pay attention to correct operation.
2.
Reduced aperture
1) Cause of occurrence
The design value of the outer diameter size of the reamer is too small; Cutting speed too low; Excessive feed rate; The main deviation angle of the reamer is too small; Improper selection of cutting fluid; When grinding the blade, the worn part of the reamer is not worn off, and the elastic recovery reduces the aperture; When reaming steel parts, if the margin is too large or the reamer is not sharp, it is easy to cause elastic recovery, resulting in reduced aperture and out of round inner hole, resulting in unqualified aperture.
2) Solution measures
Replace the outer diameter size of the reamer; Appropriately increase cutting speed; Reduce the feed rate appropriately; Appropriately increase the main deviation angle; Choose oil-based cutting fluids with good lubrication performance; Regularly exchange the reamer and grind the cutting part of the reamer correctly; When designing the size of the reamer, the above factors should be considered, or the value should be determined based on the actual situation; Perform experimental cutting, take appropriate margin, and sharpen the reamer.
3.
The hinged inner hole is not round
1) Cause of occurrence
The reamer is too long and lacks rigidity, causing vibration during reaming; The main deviation angle of the reamer is too small; Narrow hinge cutting edge band; Excessive hinge allowance; There are notches and intersecting holes on the surface of the inner hole; There are sand holes and pores on the surface of the hole; Loose spindle bearings, lack of guide sleeve, or excessive clearance between the reamer and guide sleeve, as well as deformation of the workpiece after removal due to tight clamping of thin-walled workpieces.
2) Solution measures
Reamers with insufficient rigidity can use reamers with unequal tooth pitch, and the installation of the reamer should use rigid connections to increase the main deviation angle; Select qualified reamers and control the hole position tolerance in the pre-processing process; Using unequal pitch reamers and longer and more precise guide sleeves; Select qualified blanks; When using equal pitch reamers to drill more precise holes, the spindle clearance of the machine tool should be adjusted, and the clearance of the guide sleeve should be higher or appropriate clamping methods should be used to reduce clamping force.
4.
The inner surface of the hole has obvious edges
1) Cause of occurrence
Excessive hinge allowance; The cutting angle of the reamer is too large; The hinge cutting edge band is too wide; There are pores, sand holes, and excessive spindle deviation on the surface of the workpiece.
2) Solution measures
Reduce the hinge hole allowance; Reduce the back angle of the cutting part; Grinding blade width; Select qualified blanks; Adjust the spindle of the machine tool.
5.
High surface roughness value of inner hole
1) Cause of occurrence
Cutting speed too high; Improper selection of cutting fluid; The main deviation angle of the reamer is too large, and the cutting edge of the reamer is not on the same circumference; Excessive hinge allowance; Uneven or too small hinge allowance, local surface not hinged; The swing deviation of the cutting part of the reamer exceeds the tolerance, the cutting edge is not sharp, and the surface is rough; The hinge cutting edge band is too wide; Poor chip removal during reaming; Excessive wear of the reamer; Reamer damage with burrs or broken edges on the cutting edge; There is a buildup of debris on the cutting edge; Due to material constraints, it is not suitable for zero degree or negative rake angle reamers.
2) Solution measures
Reduce cutting speed; Select cutting fluid according to the processing material; Properly reduce the main deviation angle and correctly grind and hinge the cutting edge; Reduce the hinge allowance appropriately; Improve the accuracy and quality of the bottom hole position before reaming, or increase the margin of reaming; Select qualified reamers; Grinding blade width; Reduce the number of teeth on the reamer according to the specific situation, increase the space of the chip groove, or use a reamer with a blade inclination angle to ensure smooth chip removal; Regularly replace the reamer and remove the grinding area during blade grinding; During the grinding, use, and transportation of the reamer, protective measures should be taken to avoid collision damage; For the damaged reamer, use a fine oilstone to repair it or replace it; Trim with an oilstone to meet the requirements and use a reamer with a front angle of 5 ° -10 °.
6.
The service life of the reamer is low
1) Cause of occurrence
The material of the reamer is not suitable; The reamer burns during sharpening; The selection of cutting fluid is inappropriate, the cutting fluid fails to flow smoothly, and the surface roughness value at the cutting point and hinge cutting edge after grinding is too high.
2) Solution measures
Choose the material of the reamer according to the processing material, which can be hard alloy reamer or coated reamer; Strictly control the amount of grinding and cutting to avoid burns; Regularly selecting cutting fluids correctly based on the processing materials; Regularly remove chips from the chip groove, use cutting fluid with sufficient pressure, and achieve the requirements through precision grinding or grinding.
7.
The accuracy of the hinge hole position exceeds the standard
1) Cause of occurrence
Wear of guide sleeve; The bottom end of the guide sleeve is too far from the workpiece; Short guide sleeve length, poor accuracy, and loose spindle bearings.
2) Solution measures
Regularly replace the guide sleeve; Extend the guide sleeve to improve the fitting accuracy of the gap between the guide sleeve and the reamer; Timely repair the machine tool and adjust the clearance of the spindle bearings.
8.
Reamer blade tooth breakage
1) Cause of occurrence
Excessive hinge allowance; The hardness of the workpiece material is too high; Excessive deviation of cutting edge and uneven cutting load; The main deviation angle of the reamer is too small, which increases the cutting width; When reaming deep or blind holes, there are too many chips that are not removed in a timely manner, and the blade teeth have been ground and cracked during grinding.
2) Solution measures
Modify the pre processed aperture size; Reduce material hardness or switch to negative rake angle reamers or hard alloy reamers; Control the swing within the qualified range; Increase the main deflection angle; Pay attention to timely removal of chips or use angled reamers with cutting edges; Pay attention to the quality of blade grinding.
9.
Broken hinge handle
1) Cause of occurrence
Excessive hinge allowance; When reaming conical holes, the distribution of rough and fine reaming allowance and the selection of cutting parameters are not appropriate; The space between the teeth of the reamer cutter is small, and the chips are blocked.
2) Solution measures
Modify the pre processed aperture size; Modify the allocation of allowances and select cutting quantities reasonably; Reduce the number of teeth on the reamer, increase the chip space, or grind one tooth off the gap between the teeth.
10.
The centerline of the hole after reaming is not straight
1) Cause of occurrence
The drilling deviation before reaming, especially when the aperture is small, cannot correct the original curvature due to poor rigidity of the reamer; The main deviation angle of the reamer is too large; Poor guidance makes it easy for the reamer to deviate from the direction during reaming; Excessive inverted cone in the cutting section; Displacement of the reamer at the gap in the intermittent hole; When hand reaming, excessive force is applied in one direction, forcing the reamer to tilt towards one end and damaging the verticality of the reamed hole.
2) Solution measures
Increase the process of expanding or boring holes to correct the holes; Reduce the main deviation angle; Adjust the appropriate reamer; Replace the reamer with a guiding part or an extended cutting part; Pay attention to correct operation.

You Might Also Like

Send Inquiry